Staci89 Posted September 10 Share Posted September 10 Link to comment Share on other sites More sharing options...
ThePhiladelphiaPenny Posted September 10 Share Posted September 10 This coin has been heavily damaged. You can still see the vague design of Jefferson's head, albeit heavily scratched and worn. Looks like a 2016 to me. I don't know if this was intentional damage, or just unfortunate circumstances. Did you have any questions about this coin in particular? Link to comment Share on other sites More sharing options...
Greenstang Posted September 10 Share Posted September 10 Whatever caused it was done after the coin was struck so it is just PMD. Link to comment Share on other sites More sharing options...
Popular Post RWB Posted September 10 Popular Post Share Posted September 10 (edited) On 9/10/2024 at 4:02 PM, ThePhiladelphiaPenny said: You can still see the vague design of Jefferson's head That would be quite an error. Edited September 11 by RWB Henri Charriere, ThePhiladelphiaPenny, ldhair and 1 other 1 3 Link to comment Share on other sites More sharing options...
Henri Charriere Posted September 10 Share Posted September 10 (edited) If there are no violent objections, I am going to take the liberty of calling this the 2016 "uniface" dime. All in favor, say Aye! Edited September 10 by Henri Charriere Add date. JT2 1 Link to comment Share on other sites More sharing options...
Sandon Posted September 10 Share Posted September 10 This apparent 2016-D Roosevelt dime was extensively scraped or abraded on the obverse, while the reverse was protected. I can't tell how this occurred in this case, but coins that have been embedded in another object or surface with one side exposed have been known to look like this. While there is such a thing as a uniface strike, this clearly isn't one. On 9/10/2024 at 4:02 PM, ThePhiladelphiaPenny said: You can still see the vague design of Jefferson's head, albeit heavily scratched and worn. Correct, except substitute F. D. Roosevelt for Jefferson! ThePhiladelphiaPenny 1 Link to comment Share on other sites More sharing options...
Henri Charriere Posted September 10 Share Posted September 10 On 9/10/2024 at 7:00 PM, Sandon said: .... While there is such a thing as a uniface strike, this clearly isn't one.... 'ti's true. The obverse was abraded with calculation and care for unknown reasons. Link to comment Share on other sites More sharing options...
VKurtB Posted September 11 Share Posted September 11 Shaking my head. Link to comment Share on other sites More sharing options...
Rod D. Posted September 11 Share Posted September 11 Probably got too close to a belt sander. Henri Charriere 1 Link to comment Share on other sites More sharing options...
VKurtB Posted September 11 Share Posted September 11 On 9/10/2024 at 7:52 PM, Rod D. said: Probably got too close to a belt sander. It’s clearly been machined off. Why can’t people see obvious things? JT2 and ThePhiladelphiaPenny 2 Link to comment Share on other sites More sharing options...
powermad5000 Posted September 11 Share Posted September 11 I wanted to say dryer coin, but that raised part is too perfectly centered for that. It is possible this was an experiment with a lathe. Either way, it is post mint damage. Link to comment Share on other sites More sharing options...
JT2 Posted September 11 Share Posted September 11 On 9/10/2024 at 8:52 PM, Rod D. said: Probably got too close to a belt sander. i was going to say grinder but i can see where the belt sander would work!! hahahahahahaahhaha Henri Charriere 1 Link to comment Share on other sites More sharing options...
J P M Posted September 11 Share Posted September 11 On 9/10/2024 at 11:56 PM, powermad5000 said: I wanted to say dryer coin, but that raised part is too perfectly centered for that. It is possible this was an experiment with a lathe. Either way, it is post mint damage. The raised part could just be the high spot pivot point it got stuck in the dryer, and round and round it went. Link to comment Share on other sites More sharing options...
Just Bob Posted September 11 Share Posted September 11 On 9/11/2024 at 7:20 AM, J P M said: The raised part could just be the high spot pivot point it got stuck in the dryer, and round and round it went. Yep Link to comment Share on other sites More sharing options...
powermad5000 Posted September 11 Share Posted September 11 On 9/11/2024 at 7:20 AM, J P M said: The raised part could just be the high spot pivot point it got stuck in the dryer, and round and round it went. Problem is I see absolutely no evidence of damage to the rear so if this was rolling around in a dryer situation the reverse would have at least a little damage. Sorry but I am sticking to my analysis. Link to comment Share on other sites More sharing options...
ThePhiladelphiaPenny Posted September 12 Share Posted September 12 On 9/10/2024 at 7:00 PM, Sandon said: This apparent 2016-D Roosevelt dime was extensively scraped or abraded on the obverse, while the reverse was protected. I can't tell how this occurred in this case, but coins that have been embedded in another object or surface with one side exposed have been known to look like this. While there is such a thing as a uniface strike, this clearly isn't one. Correct, except substitute F. D. Roosevelt for Jefferson! Oh my, did I type that!? Henri Charriere 1 Link to comment Share on other sites More sharing options...